CS-FLVL-COM-CS-23-PAP | Carli Suspension 3.5" Lift Commuter Leveling System PAP Front & Rear Shocks For Ford F-250/F-350 Super Duty | Diesel
For 2023-2026 Ford F-250/F-350 Super Duty | Diesel
Description
The Super Duty Commuter 2.0 system is designed for people seeking the best on-road ride quality that don’t plan to off-road their vehicle beyond low-speed trail driving. Utilizing Carli SPEC 2.0″ Diameter, Internal Reservoir shocks, we’ve developed a tune that delivers all-around comfort and ride quality designed for on-road, in town, highway, and towing/hauling.
- Experience improved handling and stability with the Carli Commuter Suspension System featuring Carli-Tuned corrosion resistant 2.0 IFP shocks.
- Shocks included in this system are valved specifically for use with stock leaf springs or Carli Progressive Add-a-Packs
- NOT RECOMMENDED for use with Carli Full Progressive Spring Packs
- System includes linear rate coil springs, front and rear shock package, brake line kit, bump stop drops, caster correction shims, radius arm drop brackets, and adjustable track bar.
- Increases wheel travel to 9" front and 13" rear.
- Fits up to 37" tires with ease for a more aggresize appearance and better offroad performance.
Wheel and Tire: Factory Wheels SHOULD NOT be run with oversized tires. They’re known to rub the radius arm, sway bar and most concerning – Brake Lines. Factory tires and factory wheels will work without issue but we DO NOT recommend running oversized tires on factory wheels. On our 3.5” Ford Systems, we recommend 17”-18” wheels, no more than 9” wide with 5.5” of backspacing with Carli Fabricated Radius Arms or 5” Backspace with factory arms; 5” will require a bit more trimming. Tires, 37×12.5” will fit with some trimming; 35” will likely fit without trimming. The more rubber, the better the small bump compliance will be at proper inflation pressures. The ride will firm up as you go larger in wheel diameter.
The "PAP" (Progressive Add-a-Pack) suffix denotes an internal valving profile matched to those running stock rear springs.
Spring Information: Factory leaf-pack modifying Progressive Add-a-Pack (maintains factory payload capacity). The F250 has a lighter rate spring pack (2 main leaf springs) than its 350 counterpart (3 main leaf springs). The F250 Add-a-Pack equipped systems are a nice improvement over stock; the F350 with the Add-a-Pack is still very stiff in the rear as the main pack doesn’t move much unless loaded. We recommend the Full Replacement Leaf Spring packs for both trucks but especially the F350 given the super-stiff factory springs. If you own an F250 built with the Tremor or high-capacity tow package, these are equipped with an F350 rear spring and should avoid the add-a-pack, as well.
Customization Information
Sway Bar Option
*REQUIRED* - The Leveling System will ride best with the Torsion Sway Bar. Maintaining the factory sway bar through use of the Sway Bar Drops or Extended Link Kit is only recommended for customers with snow-plows, in-bed campers or who are constantly hauling to the capacity of the truck.
17-26 FORD F250/350 4X4 STOCK SWAY BAR FRAME DROP BRACKET - 2.5"/3.5" LIFT
SKU: CS-FSBD-LVL-1723
- Corrects Sway Bar Geometry in Carli Leveling Suspensions
20-26 FORD F250/350 4X4 EXTENDED SWAY BAR END LINK & SWAY BAR DROP BRACKET KIT - 3.5"
SKU: CS-FELKIT-LVL-20
- Combines End Links and Drop Brackets For Perfect Sway Bar Position
- Extended Length to accommodate Leveled Trucks
- 17-4 Stainless Steel, Greaseable and Fully Rebuildable
- Excellent Articulation
- Compatible with 2.5″ & 3.5″ Suspension Systems
17-26 FORD F250/350 4X4 TORSION SWAY BAR KIT 2.5"/3.5" LIFT WITH END LINKS
SKU: CS-FTSB-LVL-17
- Direct Fitment to Carli Leveling Lifts
- Replaces Immobile Factory Sway Bar with Custom Torsion Bar
- Huge Ride Quality Improvement
- Includes CS-FEL-LVL-17 Drop Brackets and Sway Bar Links
Rear Leaf Spring Option
*REQUIRED* - The "PAP" base kit pair to stock springs or Carli add-a-packs. Add-a-Packs are NOT recommended for the F350 (or any F250 equipped with the High Capacity Tow or Tremor Package).
17-26 FORD F250/350 4X4 PROGRESSIVE ADD-A-PACK - 1" LIFT
SKU: CS-FPAP-LVL-17
- Built in the U.S.A. By Deaver Leaf Spring
- Smooth, Progressive Design
- Supplied with Bump Stop Drops, U-bolts and hardware
- Pairs to Carli Leveling Lifts, provides 1/2"-1" high rear stance
- Eliminates the Factory Block
- Load capacity is maintained, ride quality is improved
Leaf Spring Shackle
*OPTIONAL* -Much of the jarring ride of the Super Duty rear can be attributed to the factory vulcanized bushings in the leaf spring pack and shackle. The factory shackle is very strong BUT the design is not conducive to a smooth ride. The Carli shackle is constructed of 1/4″ American cold-rolled steel. The mid-length gusset ensures no deflection while the serviceable bushings offer a far superior ride to the bind of the factory bushings.
05-26 FORD F250/350 4X4 FABRICATED LEAF SPRING SHACKLE
SKU: CS-FSHACKLE-11
- Greasable and Rebuildable
- Far Better Ride than Factory Shackle
- 1/4" Steel Construction
- Fits Factory and Carli Springs
2° Pinion Shim
*OPTIONAL BUT RECOMMENDED* When modifying the rear leaf springs (add-a-pack or Full Spring Pack) of the 2017+ Super Duty platform, there's a small chance you'll induce a driveline vibration around 70mph when under power from the rear driveline. These pinion shims will correct the angle to 4°-5°, ideal for our lifted applications. Although these will not be "required" on every truck, we've found the 4°-5° spec to be superior in our applications and these are FAR easier to install initially than correctively.
05-26 FORD F250/350 4X4 FORD PINION SHIM KIT, 2 DEGREE
SKU: CS-FPSKIT-3X2
- 2° Pinion Shim Kit
- Includes new Center Pin
Adjustable Radius Arms
*OPTIONAL* - Icing on the cake, these arms have been completely redesigned for the 23+ Super Duty. They boast Limit Strap Protection for your Front Shocks, 1/4" Boxed Steel Constructions, Serviceable 17-4 Stainless Spherical Bearings and Adjustable Caster Correction up to 3.5° over stock specs to leave Death-Wobble in the rear-view.
23-26 FORD F250/350 4X4 FABRICATED RADIUS ARMS - 3.5" LIFT
SKU: CS-FARA-LVL-23
- 0.5°-2.5° of adjustable Caster correction
- 3/16 Construction, Full Length Internal Structure
- 12" Limit Straps Kit Included
- 17-4 Stainless Spherical Joint for longevity and bind free Cycling
Low Mount Steering Stabilizer
*OPTIONAL* - Bolt in steering stabilizer which compliments a Carli, or factory, high mount stabilizer. Adjustable from 70-200 psi to run neutral (no directional influence at 70psi) or at 200psi to counter the left-hand pull inherent to tires like Nitto Trail Grapplers. Run in conjunction with the Carli High Mount for the ultimate Dual, Opposing Steering Stabilizer combination that's infinitely adjustable.
23-26 FORD F250/350 4X4 LOW MOUNTSTEERING STABILIZER KIT - WITH DIFFERENTIAL GUARD
SKU: CS-FLMSS-23
- Custom Valved for Larger Tires, Adjustable Nitrogen Pressure
- Includes Differential Guard and Clamp
- Combines with High-Mount Stabilizer for Opposing Setup
High Mount Steering Stabilizer
*OPTIONAL* - Bolt in replacement for the factory stabilizer. Adjustable from 70-200 psi to run neutral (no directional influence at 70psi) or at 200psi to counter the right-hand pull inherent to tires like Toyo Mud Terrains.
17-26 FORD F250/350 4X4 HIGH MOUNT STEERING STABILIZER - STAINLESS STEEL - 2.5" & 4.5" LIFT
SKU: CS-FHMSS-17
- Long Lasting Performance and Appearance
- Bolt in Replacement for OEM Stabilizer
- Works on leveled and lifted trucks ONLY
- Not Compatible with Drop Pitman Arms
- Counters the right-hand pull inherent to tires like Toyo Mud Terrains.
Light Bar
*OPTIONAL* - The Carli Fabricated Light Bar features heavy-duty DOM steel construction, billet aluminum end caps, and compatibility with Baja Designs LP Series lights or a 40" ONX6 Arc Light Bar. Utilizing factory bumper mounting locations with no visible hardware, it provides a clean, integrated appearance while adding substantial off-road lighting capability. Lights sold separately.
17-26 FORD F250/350 4X4 FABRICATED LIGHT BAR
SKU: CS-FLB-17
- 0.120" Wall DOM Main
- Internally Gusseted, Boxed, Fabricated Horns
- Precision Fit Utilizing 4 Bumper Bolts
- Hidden Mounting Hardware = Better Aesthetic & Security
- 6061 Billet End Caps
- Accommodates Several Baja Designs Lighting Configurations
- Lights NOT INCLUDED
- Fitment: 2017-2026 Ford F250/F350
Trophy Hitch
*OPTIONAL* - Get your over-sized spare out of your bed - crank it into the factory location and secure it with our 3-way tie-down with the Carli Trophy hitch. Boasting 16,000lbs. of capacity via the 3" hitch receiver, direct bolt in installation, and up to a 38" spare tire in the factory location!
17-26 FORD F250/350 4X4 TROPHY HITCH
SKU: CS-FHITCH-1723
- Direct Bolt in, Rated to 16,000lbs., 3" Hitch Receiver
- 3/16" and 1/4" Cold-Rolled American Steel
- Utilizes Factory Winch + 3-way Tie-Down to Secure Spare
- 38" Spare Tire in the Factory Location
- May Require Exhaust Modification
- Requires 5/8" x 4" (usable shank) Hitch Pin
Application List
Ford F-250 Super Duty (2023-2026)
Component List
CS-FLC-05 Front Leveling Coils
AS-FLVLSPKG-CS20IFP-B Carli SPEC 2.0″ IFP Shocks, Front and Rear, PAP Valving
CS-FBDF-25-17 Front Bump Drops
CS-FORDBBL-LVL-17-F Front Brake Lines
CS-FCASTERSHIM-45 1° Caster Shims
CS-FATB-17 Track Bar
CS-FRAD-LVL-23 Radius Arm Drops, LVL
Details
- CS-FLVL-COM-CS-23-PAP
- CS-FLVL-COM-CS-23-PAP
- 883584169451
- Carli Suspension
- New
Categories
Shipping Information
- Item Requires Shipping
- 149.0 lbs.
- W13.0000” x H37.0000” x L12.0000”
- Free Ground Shipping | Exclusions Apply*